NRH271 & NRH272 Rotary Position Sensor

The NRH271 and NRH272 family of no-contact, Rotary Position Sensors offers the optimal combination of performance, safety and cost. All variants utilise proven Hall-effect sensing technology and are accommodated in a low-profile housing with a compact footprint.

  • No-contact, Hall-effect technology
  • Wear free – unlimited mechanical life
  • Simple mounting, low-profile design
  • Measurement angle 20-360°
  • 5V or 9-30V supply options
  • Single or dual redundant outputs
  • Analogue output – 0.5-4.5V or 0.2-4.8V
  • PWM output – 244Hz, 500Hz or 1,000Hz
  • Fail-safe outputs
  • Encapsulated electronics
  • Sealing to IP67
  • AMP or Deutsch connector options
  • Flying-lead option
  • Protective cable conduit option

The electrical output span can be set to correspond to rotations of 20° to 360°, and the positional information is determined by the angle of the supplied magnet relative to the sensor body. The maximum air gap between magnet and sensor is 7mm, while concentric offsets of up to 2mm can be tolerated with minimal impact on output linearity. The magnet can be supplied in a convenient carrier, housed in a bolt, as a plug or loose.

A choice of power supply options are available – one for connection to a regulated 5V supply and the other to a varying voltage in the range of 9-30V, such as a vehicle’s battery. The NRH271 range has a single output, while the NRH272 has a second, redundant output. In addition, the NRH272 contains two completely independent measuring circuits, each with its own power supply, meaning high-performing, safety-critical applications can easily be addressed. Furthermore, both models contain on-board diagnostic functions that mean the outputs can be put into safe, pre-defined states should an internal sensor error be detected. The versatile, factory-programmable electronics can be easily set to one of two analogue voltage output ranges or one of three PWM frequencies. In addition, the polarities of each of the analogue outputs can be independently set.

A fully-encapsulated design offers exceptional levels of performance with respect to water and dust, shock, vibration and temperature, meaning the sensor is ideal for use in hostile, on- and off-highway vehicle environments.

Connection options are industry-standard AMP Superseal (IP68 rated) or Deutsch DT04 series (IP67 rated) connectors, or simple flying leads for customer termination. The sensor can also be supplied with a protective conduit for the cabling.

 

Description

Penny & Giles NRH271 & NRH272 non-contacting, Rotary Position Sensor offers the optimal combination of performance, safety and cost. All variants utilise proven Hall-effect sensing technology and are accommodated in a low-profile housing with a compact footprint.

Features of the NRH271 & NRH272 Non-contacting Rotary Position Sensor:

  • Non-contacting, Hall-effect technology
  • Wear free – unlimited mechanical life
  • Simple mounting, low-profile design
  • Measurement angle 20-360°
  • 5V or 9-30V supply options
  • Single or dual redundant outputs
  • Analogue output – 0.5-4.5V or 0.2-4.8V
  • PWM output – 244Hz, 500Hz or 1,000Hz
  • Fail-safe outputs
  • Encapsulated electronics
  • Sealing to IP67
  • AMP or Deutsch connector options
  • Flying-lead option
  • Protective cable conduit option

The electrical output span can be set to correspond to rotations of 20° to 360°, and the positional information is determined by the angle of the supplied magnet relative to the sensor body. The maximum air gap between magnet and sensor is 7mm, while concentric offsets of up to 2mm can be tolerated with minimal impact on output linearity. The magnet can be supplied in a convenient carrier, housed in a bolt, as a plug or loose.

A choice of power supply options are available – one for connection to a regulated 5V supply and the other to a varying voltage in the range of 9-30V, such as a vehicle’s battery. The NRH271 range has a single output, while the NRH272 has a second, redundant output. In addition, the NRH272 contains two completely independent measuring circuits, each with its own power supply, meaning high-performing, safety-critical applications can easily be addressed. Furthermore, both models contain on-board diagnostic functions that mean the outputs can be put into safe, pre-defined states should an internal sensor error be detected. The versatile, factory-programmable electronics can be easily set to one of two analogue voltage output ranges or one of three PWM frequencies. In addition, the polarities of each of the analogue outputs can be independently set.

A fully-encapsulated design offers exceptional levels of performance with respect to water and dust, shock, vibration and temperature, meaning the sensor is ideal for use in hostile, on- and off-highway vehicle environments.

Connection options are industry-standard AMP Superseal (IP68 rated) or Deutsch DT04 series (IP67 rated) connectors, or simple flying leads for customer termination. The sensor can also be supplied with a protective conduit for the cabling.

The Penny & Giles product range comprises a broad selection of joysticks, sensors and solenoids for use on commercial vehicles and industrial equipment.

The products are the legacy of the Penny & Giles company founded in 1956 and acquired by Curtiss Wright in 2002.

The present-day product range includes: linear and rotary position sensors; LVDT and RVDT transducers; joysticks; studio faders; digital panel meters; and solenoid actuators for a wide range of industrial motion control applications.

Their joystick controls are suitable for commercial vehicle applications for both on- and off-highway use. These include construction and agricultural vehicles, material handling and other specialty vehicles. They are also suitable for use with industrial equipment such as robotics. Their finger-operated joystick controllers are designed for the smooth, precise control of critical functions in a variety of industrial applications where a Human-Machine Interface (HMI) is required. They also have rugged joystick controllers are designed for the more demanding installations found within operator cabs for off-highway vehicles. A wide range of linear position sensors, tilt sensors, rotary sensors, linear displacement transducers and linear potentiometers that offer distinct advantages in reliability, stability and compactness.

For the full range of Penny & Giles products

Follow us on Facebook

Content missing